Skip to main content

ALL about the Production of the Volkswagen XL1



Hey Guys
I've already told you about the Debut of the most aerodynamic production car yesterday, today I want to tell you something about the production-steps of the Volkswagen XL1. (Finally I have a reason to look forward to the Geneva Motor Show!)

Manufacturing in Osnabrück

The XL1 is manufactured by Volkswagen Osnabrück GmbH. In the former Karmann plants there, around 1,800 employees produce such cars as the Golf Cabriolet and the new Porsche Boxster.
As is usual in the framework of mass produced vehicles like the Golf Cabriolet, many components − such as the monocoque, engine, motor, suspensions and battery − are supplied by other plants and external suppliers. However, in the small production series for the XL1, the specialists from Osnabrück are not pursuing the classic path of large-scale production, rather they are practicing automotive handcrafting. Nonetheless, the XL1 production processes implemented in Osnabrück are highly innovative and unique. There were no previous examples of the individual production steps anywhere in the world, because no other car has been produced so thoroughly in a similar composite material.
Over the long term, other Group brands will also benefit from the numerous innovations implemented in the XL1.

The production process for the new XL1 in detail:

Production stage I – bodyshell frame

Production of the XL1 begins with delivery of the CFRP monocoque, which is produced by a supplier in Austria using the RTM process. The manufacturing process itself was developed over several years in close cooperation with Volkswagen. In Osnabrück, the monocoque is mounted to an assembly support plate; this is where the body is built – but without doors or lids. This first body production stage is referred to as the “bodyshell frame”. At this station, all parts are moved to their prescribed design
positions by special fixtures. This approach is necessary to maintain the tight manufacturing tolerances.
The various interior and exterior surfaces of the monocoque itself are pretreated in advance. This pretreatment is necessary to attain tight gaps and smooth surfaces. Background: In the interior of the XL1, many of these CFRP surfaces were intentionally left uncovered by trim panels, and so the high-tech material remains visible. The individual CFRP components are joined to one another in the bodyshell frame by gluing – a highly complex and unique process in manufacturing technology. The operation of mounting the roof section to the monocoque illustrates just how complex this process is:
Unlike welded metal parts, the roof of the XL1 cannot simply be placed on the monocoque. Rather the strength of the adhesive material must compensate for all fit gaps of the monocoque-roof side member structure and the different material thicknesses of the laminated roof. Therefore, this part is made to hover over the monocoque before gluing. The gluing process itself is performed according to a precisely defined sequence with precisely defined curing times.

Over the further course of production stage I, the boot pan is brought into position with the water channel, and it is glued and screw fastened. In addition, all structural and exterior skin parts (rear crossmembers, rear termination part, side panels front and rear) are positioned and screwed via a sled fixture. Last but not least, employees check and document the dimensional tolerances of the entire assembly as the final step of every production stage. Each individual part of the XL1 is also documented with a serial number and its production history.



Production stage II – door assembly

In parallel to production stage I, the two wing doors are produced in a separate production stage, including their crash reinforcements. Volkswagen developed its own tool for this, which is used to fit the doors to adjoining body parts with millimetre precision to satisfy the extremely tight production tolerances – even before it is placed in the monocoque. This is the only way to assure that all requirements
are fulfilled in the installed state, such as the defined joint seam dimension and uniform transitions between the surfaces. Unlike sheet metal parts, carbon elements cannot be reshaped afterwards.

Production stage III – body assembly

At the third production station, the bodyshell frame is placed on a new fixture. Here, all body parts are assembled to achieve the specified gap dimensions and flush mounting precisions. These parts include the wing doors, bonnet, boot lid, front bumper and various small parts. Adjustment of the wing doors is a special challenge, because a precise fit must be assured to the roof and side body surfaces.

Production stage IV – painting

A total of 32 exterior skin parts are painted on the XL1; six of them are visible carbon parts. The CFRP parts are specially prepared for painting in the framework of XL1 production. Background: To fulfil the quality standard of a Class A paint job despite a minimally thin and therefore lightweight paint layer, in the RTM process a special fleece layer or resin film is added to the parts as a cover coat. Compared to conventional CFRP paints used in the industry, this yields a weight reduction of over 50 per cent.
This innovative CFRP painting process owes its implementation to intensive fundamental work by the Volkswagen Technical Deveopment Centre in Wolfsburg and an associated series of tests by paint experts at the Osnabrück plant.

The paint itself consists of three layers. The primer with a filler material is followed by the base paint – the coloured layer. Then the final layer or clearcoat is applied, which provides a high level of scratch resistance and UV resistance. In the interior, on the other hand, a decorative “matt pearl grey” paint is applied, or – on visible carbon parts such as the sills – a matt clearcoat. The same applies to the
roof structure on which Volkswagen omitted trim parts in the interest of attaining optimal weight and maximising open space for the occupants.


Production stage V – front car section

Following painting, all components are transported to final assembly. The first step here is to join the front body section to the prefabricated floor pan. The module of this floor plan consists of components such as the double wishbone front suspension with swivel bearing (produced from die-cast aluminium), anti-roll bar (produced from CFRP), a small 12-Volt battery for the vehicle electrical system and the front ceramic brake discs. Also integrated in front is the high-voltage battery for the plug-in hybrid drive. Another special aspect is the mounting position of the air conditioner: the unit is typically mounted in the vehicle interior. For packaging reasons, however, this is not possible in the XL1. Therefore, the air conditioner is installed in a special insulated capsule in the car’s front section. Automatic testing of the
vehicle’s electrical system and preliminary startup of all electronic components are also performed at the ITC (Startup and Test Centre) in this production stage.

Production stage VI – rear section and interior

The classic merging of the drive unit with the body occurs after assembly of the front end. The entire drive unit (two-cylinder TDI engine, E-motor and 7-speed DSG) is installed in the rear section of the XL1. The rear axle produced from die-cast aluminium together with final drive shafts and ceramic brake discs, as well as the CFRP anti-roll bar, complete the components integrated at the rear.
In parallel, the cockpit is installed at this station via its magnesium supports. Unlike in mass production, no provisions were made for preassembling the XL1 cockpit due to the small production volume. Instead, all individual cockpit parts are mounted inside the vehicle superstructure. The dashboard itself consists of a moulded wood fibre material, which is just 1.4 mm thick and is produced in a special pressing process.


Production stage VII – windscreen, doors and wheels

The XL1 now takes on more of its final shape. After assembly of the drive unit, the laminated glass windscreen is installed, which is only 3.2 mm thick. The wing doors (including outside door mechanisms) are reinstalled; their exact positions and alignments were already set in production stage II. The bonnet is also mounted on the monocoque with centering pins. Last but least, the XL1 gets its magnesium wheels. They are fitted with low rolling resistance tyres sized 115/80 R15 (front) and 145/55 R16 (rear).

Production stage VIII – final assembly of the doors

The wing doors are the most complex add-on components of the XL1 body. After installing the painted door and integrating the window mechanisms, special assembly fixtures are used to glue the polymer side windows into place. The larger part of the windows is permanently joined to the exterior door skin for packaging reasons, while a segment of the lower area of the side windows can be opened. Finally, the reversing cameras are placed in their housings, and the e-mirrors that serve as digital door mirrors are mounted to the exterior CFRP of the door.

Production stage IX – startup

In the context of quality assurance, all electronic control modules and their individual software and
wire harness are checked. At the same time, the control modules are interconnected with the vehicle’s
specific wire harness. Now, final startup of the XL1 is performed. First, the entire high-voltage system
is checked. For this purpose, “simulated” isolation faults are introduced to test the system’s emergency
shutoff functionality. The next step is to start up the internal combustion engine; all actuators and sensors of the TDI engine are checked, and parameter values at its first startup are compared to target
values. In parallel, employees adjust the camera-based door mirror (e-Mirror); the correct visual field of the e-Mirror is optimally tuned using a special computer program.
After all systems have been started up, a check is made of all electrical equipment; this too is done according to a precisely observed checklist. Only then is the production of the XL1 completed with a test drive to check dynamic vehicle functions. Now the world’s most efficient car can be delivered!

Wow, right? WOW! Can't wait to see it at the Geneva Motor Show in two weeks! :)

Lisa

Comments

  1. Love this, thanks for sharing!

    ReplyDelete
  2. Thanks a lot Lisa, I really enjoyed reading about the production process :*

    ReplyDelete
  3. Any first Test Drive Review on this?

    ReplyDelete

Post a Comment

What do you think?

Share your Opinion!

Popular posts from this blog

Gallery: 15th Bodensee Oldtimer Rallye in Friedrichshafen (July 5th 2014)

Hey Guys

For the 15th time now the Bodensee Oldtimer Rallye takes place this Weekend, all around the beautiful region of the Lake of Constance. During the morning I took these Pictures at the official start at the Zeppelin Museum right next to the harbor and the Lake. If you are interested, the Cars should return to Friedrichshafen City by 4 pm. This time more than 80 Cars attended the Rallye, see down here a first Part of Pictures, the second one is already online over at Hyyperlic.com: 15. Bodensee Oldtimer Rallye in Friedrichshafen - check it out!

Porsche enters third 919 HYBRID LMP1 Race Car in 2015 Le Mans 24h Race

Porsche has announced the entry of a third Porsche 919 Hybrid LMP1 race car for the 2015 Le Mans 24 Hours in France on 13/14 June. As a dress rehearsal for the event, the car will also be entered in the Six Hours World Endurance Championship (WEC) race at the Spa-Francorchamps circuit (Belgium) on 2 May.

Geneva Motor Show 2014 - List of Premieres

Hey Guys

On Tuesday it's finally this time of the year again .. the Geneva Motor Show takes place! As every year at the beginning of March, for the fifth time now, I'm travelling to southern Switzerland so see and feel all the Cars by myself, and for sure I'm reporting for you. And so my Question to you is - WHAT DO YOU WANT TO SEE?

As I want to focus on the Cars and Premieres and Manufacturers that interest YOU I have collected a small list of the already announced Premieres at the Geneva Motor Show 2014 and you are invited to comment your wishes below here, on my Facebook Page of write me via Twitter to @thecaraddict.

The Geneva Motor Show 2014 is open to the Public from MArch 6th to 16th, I'll be there on Tuesday and Wednesday, so 4th to 5th to take all the Pictures and Videos you want to see!